語言
Magnetron sputtering (磁控濺射台))

新聞資訊

熱門關鍵詞

聯係91guochan

名 稱:蘇州91shipin電子科技有限公司

電 話:0512-58987901

傳 真:0512-58987201

郵 箱:sales@tonertimes.com

地 址:江蘇省張家港經濟開發區複興路2號B06棟1樓215600PRC

網 址:www.tonertimes.com

Name: Suzhou cycas  Microelectronics Co., Ltd.

Tel.: 0512-58987901

Fax: 0512-58987201

Email: sales@tonertimes.com

Address: 1st floor,B06 building,No.2,Fuxing Road,Zhangjiagang Economic Development Zone,Jiangsu Province 215600PRC

Website: www.tonertimes.com 

微波等離子去膠機操作規程 Operation procedures of microwave plasma degummer:

您的當前位置: 首 頁 >> 新聞資訊 >> 技術知識

微波等離子去膠機操作規程 Operation procedures of microwave plasma degummer:

發布日期:2018-02-01 作者:www.tonertimes.com 點擊:

微波等離子去膠機操作規程:

  1、自動切割小車應經空車運轉,並選定切割速度;

  2、使用釷、鎢電極應符合JGJ33-2001第12.7.8條規定;

  3、高頻發生器應設有屏蔽護罩,用高頻引弧後,應立即切斷高頻電路;

  4、應檢查並確認電源、氣源、水源無漏電、漏氣、漏水,接地或接零安全可靠;

  5、操作人員應站在上風處操作。可從工作台下部抽風,並宜縮小操作台上的敞開麵積;

  6、小車、工件應放在適當位置,並應使工件和切割電路正極接通,切割工作麵下應設有溶渣坑;

  7、微波等離子去膠機應根據工件材質、種類和厚度選定噴嘴孔徑,調整切割電源、氣體流量和電極的內縮量;

  8、當空載電壓過高時,應檢查電器接地、接零和割炬手把絕緣情況,應將工作台與地麵絕緣,或在電氣控製係統安裝空載斷路斷電器;

  9、微波等離子去膠機操作人員必須戴好防護麵罩、電焊手套、帽子、濾膜防塵口罩和隔音耳罩。不戴防護鏡的人員嚴禁直接觀察等離子弧,裸露的皮膚嚴禁接近等離子弧。      

 Operation procedures of microwave plasma degummer:

1. The automatic cutting car shall be operated by empty car and the cutting speed shall be selected;

2. Thorium and tungsten electrodes shall be used in accordance with article 12.7.8 of jgj33-2001;

3. The high frequency generator shall be equipped with shielding shield, and the high frequency circuit shall be cut off immediately after high frequency arc striking;

4. Check and confirm that the power supply, air source and water source are free of leakage, air leakage and water leakage, and that the grounding or neutral connection is safe and reliable;

5. The operator shall stand in the upwind position to operate. The air can be drawn from the lower part of the worktable, and the open area on the worktable should be reduced;

6. The trolley and workpiece shall be placed in proper position, and the positive pole of the workpiece and the cutting circuit shall be connected, and the slag dissolving pit shall be set under the cutting working face;

7. Microwave plasma degumming machine should select nozzle aperture according to workpiece material, type and thickness, adjust cutting power, gas flow and electrode shrinkage;

8. When the no-load voltage is too high, check the electrical grounding, zero connection and torch handle insulation, insulate the workbench from the ground, or install the no-load breaker in the electrical control system;

9. Operators of the microwave plasma degumming machine must wear protective masks, welding gloves, hats, filter dust masks and acoustic earmuffs. Personnel without protective glasses are strictly forbidden to observe plasma arc directly, and exposed skin is strictly forbidden to approach plasma arc.


等離子刻蝕機

本文網址:http://www.tonertimes.com/news/381.html

相關標簽:等離子刻蝕機

Z近瀏覽: