語言
Magnetron sputtering (磁控濺射台))

新聞資訊

熱門關鍵詞

聯係91shipin

名 稱:蘇州91xjcc下载官网電子科技有限公司

電 話:0512-58987901

傳 真:0512-58987201

郵 箱:sales@tonertimes.com

地 址:江蘇省張家港經濟開發區複興路2號B06棟1樓215600PRC

網 址:www.tonertimes.com

Name: Suzhou cycas  Microelectronics Co., Ltd.

Tel.: 0512-58987901

Fax: 0512-58987201

Email: sales@tonertimes.com

Address: 1st floor,B06 building,No.2,Fuxing Road,Zhangjiagang Economic Development Zone,Jiangsu Province 215600PRC

Website: www.tonertimes.com 

金屬標牌腐蝕機的蝕刻液蝕刻工藝介紹Introduction to etching process of etching solution of metal plate etching machine

您的當前位置: 首 頁 >> 新聞資訊 >> 技術知識

金屬標牌腐蝕機的蝕刻液蝕刻工藝介紹Introduction to etching process of etching solution of metal plate etching machine

發布日期:2018-11-24 作者:www.tonertimes.com 點擊:

 常見問題如下:

  1. 1mi標牌蝕刻機能腐蝕的材料長度不限,而有效蝕刻是1000mm指長度嗎,然後有效寬度是800mm ?

  答:有效蝕刻1000mm:是指蝕刻機藥水噴淋區域的長度是1000mm(此處僅為蝕刻機規格大小,腐蝕區大小決定加工的產量和腐蝕的深度),材料經過噴淋區域的長度越長對應腐蝕的時間就越長深度就越深,蝕刻機越長多能承載的工件就越多,所以產量也越高;

  有效寬度800mm:是指工件800mm寬度以下的產品都可以生產加工,不得超出800mm。

  2. 輸送軸間距40mm是指每個軸的距離嗎?

  答:是的

  3. 此1米不鏽鋼蝕刻機能腐蝕材料深度是多少,資料沒有看到?腐蝕深度是通過調節壓力調整表對嗎?

  答:Z大深度為0.3mm,工件腐蝕的深度根據藥水濃度、壓力、腐蝕時間來控製。

  4. 檔水棍的作用是什麽?腐蝕需要接水進入嗎?

  答:擋水的棍作用:工件從噴淋區域傳送出來時會有腐蝕液殘留,此擋水棍通過上棍下棍上下壓合工件的方式把工件上殘留的腐蝕液清除掉。

等離子刻蝕機

  5. 金屬等離子刻蝕機用的蝕刻液是什麽?蝕刻液再生如何操作?材料在哪裏能買的到,請提供材料名稱和類型

  答:腐蝕液為三氯化鐵,蝕刻液再生可添加還原劑還原,材料91xjcc下载官网可以提供全套耗材供應商。

  6. 說明一下腐蝕的蝕刻工藝流程,我看到資料上機器有噴淋、發熱管,還有過濾器。

  答:腐蝕原理:2FeCl3+Fe=3FeCl2,材料上被腐蝕處就是鐵離子的減少形成的。

  7. 蝕刻液的作用,那麽客戶要完成後有顯示顏色,這要客戶先調好腐蝕液的顏色對嗎?一般腐蝕液有幾種顏色可以用?

  答:利用蝕刻液腐蝕後會漏出材料的本色,腐蝕工藝是沒有上色的,上色需後期處理。

  8. 腐蝕的時間是多久?腐蝕好了即幹嗎?需要放置多久時間?

  答:腐蝕的時間根據需求深度來控製,深度越深腐蝕時間就越長,腐蝕後用清水衝洗表麵,待水風幹即可

       Common problems are as follows: 

       1. The length of materials that can be corroded by 1mi label etching is unlimited, but is the effective etching 1000mm refers to the length, and then the effective width is 800mm?

       Answer: effective etching 1000mm: it means that the length of the spray area of the chemical solution of the etching machine is 1000mm (here only refers to the size of the etching machine, and the size of the corrosion area determines the processing yield and corrosion depth). The longer the material passes through the spray area, the longer the corresponding corrosion time is, the deeper the depth is. The longer the etching machine is, the more workpieces it can carry, so the higher the yield is; Effective width 800mm: it means that products with width less than 800mm can be produced and processed, and shall not exceed 800mm.

     2. Does the distance between conveying shafts of 40mm refer to the distance between each shaft? 

     Answer: Yes, 

     3. What is the depth of corrosion material of this 1m stainless steel etching machine? The data is not seen? The corrosion depth is adjusted by adjusting the pressure adjustment table, right?

     Answer: the maximum depth is 0.3mm, and the corrosion depth of workpiece is controlled according to the concentration of chemical water, pressure and corrosion time.

     4. What is the function of the water retaining stick? Does the corrosion need to be connected with water? 

     Answer: the water retaining stick function: when the workpiece is transmitted from the spray area, there will be residual corrosive liquid. The water retaining stick can remove the residual corrosive liquid on the workpiece by pressing the workpiece up and down with the upper stick and the lower stick.

    5. What is the etching solution for metal plasma etching machine? How to operate the regeneration of etching solution? Where can I buy the material? Please provide the name and type of the material

     Answer:the etching solution is ferric chloride, the regeneration of etching solution can be reduced by adding reductant, and we can provide a complete set of consumables supplier.

   6. Explain the etching process of corrosion. I can see that the machine on the data has spray, heating pipe and filter.

Answer: principle of corrosion: 2fecl3 + Fe = 3fecl2. The corroded part of the material is formed by the reduction of iron ions.

   7. For the function of etching solution, the customer needs to display the color after completion, which requires the customer to adjust the color of the etching solution first, right? Generally, there are several colors of the etching solution that can be used?

 Answer:the original color of the material will leak out after etching with the etching solution, the etching process is not colored, and the coloring needs post-processing.

  8. How long is the corrosion time? What happens when the corrosion is good? How long does it need to be placed? 

Answer:the corrosion time is controlled according to the required depth. The deeper the depth is, the longer the corrosion time will be. After the corrosion, wash the surface with clean water and wait for the water to air dry.

    

      

本文網址:http://www.tonertimes.com/news/417.html

相關標簽:等離子刻蝕機

Z近瀏覽: